Smith & Wesson HOGUE • K/L Frame SQUARE Full Size Fingergroove Grips
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Check out Our Unique Grip Section For Limited run and hard to find grips!
Fits the following Smith and Wesson K/L Frame SQUARE Butt Models:
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation. Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Check out Our Unique Grip Section For Limited run and hard to find grips!
Fits the following Smith and Wesson K/L Frame SQUARE Butt Models:
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation. Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Check out Our Unique Grip Section For Limited run and hard to find grips!
Fits the following Smith and Wesson K/L Frame SQUARE Butt Models:
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation. Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.