Smith & Wesson J Frame Square Full Dragonscale/FlatTop Checker • All Wood Species • Pau Ferro Shown
NOTE: Current inventory levels are based on HOGUE stock, we order these grips as needed at this time. If we begin selling more of these we will stock them. This will usually add 1 week to delivery time, however if Hogue runs out it may take up to 30 days. Please ask first if you want a definitive lead time.
S&W J Frame Square HOGUE Full Grips featuring our Exclusive Dragonscales with FlatTop Checker engraving. Choose optional Genuine S&W 3/8” Silver Medallions or Engrave the top section with Logos, Names, Monograms, etc. Choose from Goncalo Alves, Pau Ferro (Shown), Cocobolo, Rosewood, Camouflage (Laminate), or Kingwood. If you have something else in mind go to our Home Page and create your own unique grips!
These grips are Hogue’s Monogrip single piece set, they come with the replacement mounting system which incorporates an alignment pin into the fastening system with the screw on the bottom. S&W Medallions are 3/8” version on J-Frame models, These are Factory original S&W Medallions!
Fits the following Smith and Wesson J-Frame Square Butt Models:-31, 35-
and the following Square Butt Models: 30, 32, 33, 34, 36, 37, 43, 50, 51, 60, 63, 651
Will also fit the early I-Frame models. To differentiate between Round and Square Butt, measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round Butts will measure around 1" and Square Butts will be over 1 1/4".
Does NOT fit Polymer Bodyguard models(BG38)
J Frame Round Vs Square Vs Polymer Bodyguard
-J frame square butt revolvers hold 5(five) .38 caliber bullets in cylinder; they are not very common compared to round butt J frames. This grip is a one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the 5/8" stock pin be removed and replaced with a shorter 1/2" pin that is supplied with the grip. The stock pin is too wide and will not allow our grip to slide on. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
NOTE: Current inventory levels are based on HOGUE stock, we order these grips as needed at this time. If we begin selling more of these we will stock them. This will usually add 1 week to delivery time, however if Hogue runs out it may take up to 30 days. Please ask first if you want a definitive lead time.
S&W J Frame Square HOGUE Full Grips featuring our Exclusive Dragonscales with FlatTop Checker engraving. Choose optional Genuine S&W 3/8” Silver Medallions or Engrave the top section with Logos, Names, Monograms, etc. Choose from Goncalo Alves, Pau Ferro (Shown), Cocobolo, Rosewood, Camouflage (Laminate), or Kingwood. If you have something else in mind go to our Home Page and create your own unique grips!
These grips are Hogue’s Monogrip single piece set, they come with the replacement mounting system which incorporates an alignment pin into the fastening system with the screw on the bottom. S&W Medallions are 3/8” version on J-Frame models, These are Factory original S&W Medallions!
Fits the following Smith and Wesson J-Frame Square Butt Models:-31, 35-
and the following Square Butt Models: 30, 32, 33, 34, 36, 37, 43, 50, 51, 60, 63, 651
Will also fit the early I-Frame models. To differentiate between Round and Square Butt, measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round Butts will measure around 1" and Square Butts will be over 1 1/4".
Does NOT fit Polymer Bodyguard models(BG38)
J Frame Round Vs Square Vs Polymer Bodyguard
-J frame square butt revolvers hold 5(five) .38 caliber bullets in cylinder; they are not very common compared to round butt J frames. This grip is a one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the 5/8" stock pin be removed and replaced with a shorter 1/2" pin that is supplied with the grip. The stock pin is too wide and will not allow our grip to slide on. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
NOTE: Current inventory levels are based on HOGUE stock, we order these grips as needed at this time. If we begin selling more of these we will stock them. This will usually add 1 week to delivery time, however if Hogue runs out it may take up to 30 days. Please ask first if you want a definitive lead time.
S&W J Frame Square HOGUE Full Grips featuring our Exclusive Dragonscales with FlatTop Checker engraving. Choose optional Genuine S&W 3/8” Silver Medallions or Engrave the top section with Logos, Names, Monograms, etc. Choose from Goncalo Alves, Pau Ferro (Shown), Cocobolo, Rosewood, Camouflage (Laminate), or Kingwood. If you have something else in mind go to our Home Page and create your own unique grips!
These grips are Hogue’s Monogrip single piece set, they come with the replacement mounting system which incorporates an alignment pin into the fastening system with the screw on the bottom. S&W Medallions are 3/8” version on J-Frame models, These are Factory original S&W Medallions!
Fits the following Smith and Wesson J-Frame Square Butt Models:-31, 35-
and the following Square Butt Models: 30, 32, 33, 34, 36, 37, 43, 50, 51, 60, 63, 651
Will also fit the early I-Frame models. To differentiate between Round and Square Butt, measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round Butts will measure around 1" and Square Butts will be over 1 1/4".
Does NOT fit Polymer Bodyguard models(BG38)
J Frame Round Vs Square Vs Polymer Bodyguard
-J frame square butt revolvers hold 5(five) .38 caliber bullets in cylinder; they are not very common compared to round butt J frames. This grip is a one-piece Monogrip design. They are ambidextrous allowing both right and left handed use. Installation is easy requiring the 5/8" stock pin be removed and replaced with a shorter 1/2" pin that is supplied with the grip. The stock pin is too wide and will not allow our grip to slide on. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
If you would like to purchase a SOLD OUT set of Grips they can be recreated easily in our Custom Build Section. Check our Custom Build Section to see if we have stock available.