Smith & Wesson HOGUE • K/L Frame Round Full Size Fingergroove Grips
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Medallions - 3/8” Small Original OEM S&W are Silver Only. 15mm Medallions are available in .999 Silver & 24k Gold Plate. The customizing form has check boxes to choose your color. Please do NOT check a 15mm box if you purchased 3/8” medallions as this will delay putting your order into our schedule.
Check out Our Unique Grip Section For Limited run and hard to find grips!
Note: Hogue will not warranty wood grips for the S&W 500, 460 and Governor as severe recoil can crack the grip.
Fits the following Smith and Wesson K/L Frame Round Butt Models:-69, 242, 296, 386, 396, 520(7 shot model), 619, 620, 646, 647, 696, 986-and the following models are either Round or Square Butts: 10, 12, 13, 14, 15, 17, 19, 64, 65, 66, 67, 547, 586, 617, 681, 686
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation.Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidexterous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith models 460, 500, and Governor use the same grips as the K/L round butt frame revolvers. The wood and G10 grips that we make for the K/L round butt frames will break when installed and fired on these models. We CANNOT warranty any wood or G10 grip that was installed on one of these models.
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Medallions - 3/8” Small Original OEM S&W are Silver Only. 15mm Medallions are available in .999 Silver & 24k Gold Plate. The customizing form has check boxes to choose your color. Please do NOT check a 15mm box if you purchased 3/8” medallions as this will delay putting your order into our schedule.
Check out Our Unique Grip Section For Limited run and hard to find grips!
Note: Hogue will not warranty wood grips for the S&W 500, 460 and Governor as severe recoil can crack the grip.
Fits the following Smith and Wesson K/L Frame Round Butt Models:-69, 242, 296, 386, 396, 520(7 shot model), 619, 620, 646, 647, 696, 986-and the following models are either Round or Square Butts: 10, 12, 13, 14, 15, 17, 19, 64, 65, 66, 67, 547, 586, 617, 681, 686
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation.Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidexterous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith models 460, 500, and Governor use the same grips as the K/L round butt frame revolvers. The wood and G10 grips that we make for the K/L round butt frames will break when installed and fired on these models. We CANNOT warranty any wood or G10 grip that was installed on one of these models.
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.
NOT FOR USE ON X-FRAME OR Z-FRAME FIREARMS!
Medallions - 3/8” Small Original OEM S&W are Silver Only. 15mm Medallions are available in .999 Silver & 24k Gold Plate. The customizing form has check boxes to choose your color. Please do NOT check a 15mm box if you purchased 3/8” medallions as this will delay putting your order into our schedule.
Check out Our Unique Grip Section For Limited run and hard to find grips!
Note: Hogue will not warranty wood grips for the S&W 500, 460 and Governor as severe recoil can crack the grip.
Fits the following Smith and Wesson K/L Frame Round Butt Models:-69, 242, 296, 386, 396, 520(7 shot model), 619, 620, 646, 647, 696, 986-and the following models are either Round or Square Butts: 10, 12, 13, 14, 15, 17, 19, 64, 65, 66, 67, 547, 586, 617, 681, 686
To differentiate between Round and Square Butt, Measure the flat area on the very bottom of your grip. This is the surface that commonly has the serial number located on it. Round butts will measure under 1 ¼” and Square butts will be over 1 ¼”.
K and L frames have the same grip frame and use the same grip. The K has been made since the '20s and there are a tremendous amount in circulation.Hogue grips for Smith & Wesson revolvers are the one-piece Monogrip design. They are ambidexterous allowing both right and left handed use. Installation is easy requiring the stirrup to be simply snapped over the existing stock pin. The grip then slides up from the butt, with one screw securing the grip through the butt. All necessary hardware is provided.
For More information see the THE MONOGRIP CONCEPT on Hogue’s website. This grip is an open backstrap design for optimum trigger reach. Some rubber and nylon grips have a "speedloader" cut out on one side only some are cut out on both sides - Wood grips are cut out on both sides. Smith and Wesson produces a 5-shot 44 Magnum revolver that is on an L frame. MODEL 69
Smith models 460, 500, and Governor use the same grips as the K/L round butt frame revolvers. The wood and G10 grips that we make for the K/L round butt frames will break when installed and fired on these models. We CANNOT warranty any wood or G10 grip that was installed on one of these models.
Smith & Wesson 2100 Roosevelt Springfield, MA 01102800 331-0852 - Fax: 413 747 3317 - Email: ga@smith-wesson.com
www.smith-wesson.com.